Rabbit RCM3200 Manual de usuario Pagina 45
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
User’s Manual 39
6.2.1 IP Addresses Explained
IP (Internet Protocol) addresses are expressed as 4 decimal numbers separated by periods,
for example:
216.103.126.155
10.1.1.6
Each decimal number must be between 0 and 255. The total IP address is a 32-bit number
consisting of the 4 bytes expressed as shown above. A local network uses a group of adja-
cent IP addresses. There are always 2
N
IP addresses in a local network. The netmask (also
called subnet mask) determines how many IP addresses belong to the local network. The
netmask is also a 32-bit address expressed in the same form as the IP address. An example
netmask is:
255.255.255.0
This netmask has 8 zero bits in the least significant portion, and this means that 2
8
addresses are a part of the local network. Applied to the IP address above
(216.103.126.155), this netmask would indicate that the following IP addresses belong to
the local network:
216.103.126.0
216.103.126.1
216.103.126.2
etc.
216.103.126.254
216.103.126.255
The lowest and highest address are reserved for special purposes. The lowest address
(216.102.126.0) is used to identify the local network. The highest address
(216.102.126.255) is used as a broadcast address. Usually one other address is used for the
address of the gateway out of the network. This leaves 256 - 3 = 253 available IP
addresses for the example given.
- RabbitCore RCM3200 1
- Rabbit Semiconductor Inc 2
- Trademarks 2
- TABLE OF CONTENTS 3
- Appendix D. Power Supply 103 5
- Notice to Users 115 5
- Index 117 5
- Schematics 121 5
- 1. INTRODUCTION 7
- Table 1. RCM3200 Features 8
- User’s Manual 3 9
- 1.4 How to Use This Manual 10
- 2. HARDWARE SETUP 11
- Do not press down 12
- PC COM port 13
- 8 RabbitCore RCM3200 14
- 2.3 Run a Sample Program 15
- 2.4 Where Do I Go From Here? 16
- 3. RUNNING SAMPLE PROGRAMS 17
- 3.2 Sample Programs 18
- User’s Manual 13 19
- 14 RabbitCore RCM3200 20
- 4. HARDWARE REFERENCE 21
- Headers J1 and J2 are 22
- Backup Battery 23
- 18 RabbitCore RCM3200 24
- User’s Manual 19 25
- 20 RabbitCore RCM3200 26
- User’s Manual 21 27
- 4.2 Serial Communication 28
- DIAG connector on 29
- LNK), one to 29
- ACT), and one to indicate 29
- 4.3 Serial Programming Cable 30
- 26 RabbitCore RCM3200 32
- 4.4 Other Hardware 33
- 4.5 Memory 34
- 5. SOFTWARE REFERENCE 35
- 30 RabbitCore RCM3200 36
- 5.2 Dynamic C Function Calls 37
- RS232.LIB 38
- PACKET.LIB 38
- User’s Manual 33 39
- RETURN VALUE 39
- 5.3 Upgrading Dynamic C 40
- 6. USING THE TCP/IP FEATURES 41
- 36 RabbitCore RCM3200 42
- User’s Manual 37 43
- 38 RabbitCore RCM3200 44
- User’s Manual 39 45
- 40 RabbitCore RCM3200 46
- User’s Manual 41 47
- 42 RabbitCore RCM3200 48
- User’s Manual 43 49
- User’s Manual 45 51
- 46 RabbitCore RCM3200 52
- 6.7 Where Do I Go From Here? 53
- 48 RabbitCore RCM3200 54
- User’s Manual 49 55
- Please refer to the RCM3200 56
- Exclusion 57
- 52 RabbitCore RCM3200 58
- User’s Manual 53 59
- A.2 Bus Loading 60
- I/O read and write cycles 61
- 56 RabbitCore RCM3200 62
- = –55°C to +125°C, V 63
- = 3.0 V to 3.6 V 63
- 58 RabbitCore RCM3200 64
- A.5 Conformal Coating 65
- A.6 Jumper Configurations 66
- PPENDIX B. PROTOTYPING BOARD 67
- B.1 Introduction 68
- User’s Manual 63 69
- 64 RabbitCore RCM3200 70
- User’s Manual 65 71
- B.3 Power Supply 72
- User’s Manual 67 73
- MEASUREMENT 74
- Connector Pinout 75
- Prototyping Board 76
- User’s Manual 71 77
- 72 RabbitCore RCM3200 78
- PPENDIX C. LCD/KEYPAD MODULE 79
- 74 RabbitCore RCM3200 80
- Contrast 81
- Adjustment 81
- C.3 Keypad Labeling 82
- C.4 Header Pinouts 83
- 78 RabbitCore RCM3200 84
- User’s Manual 79 85
- Bezel/Gasket 86
- User’s Manual 81 87
- C.7.3 LCD Display 89
- STDIO string functions 95
- C.7.4 Keypad 104
- library 104
- C.8 Sample Programs 107
- 102 RabbitCore RCM3200 108
- APPENDIX D. POWER SUPPLY 109
- 165 mA·h 110
- D.2 Optional +5 V Output 110
- E.1 Overview 111
- E.2 Header J6 112
- E.3 Using Parallel Port F 113
- 108 RabbitCore RCM3200 114
- Bits Value Description 115
- Table E-3. PWM Outputs 116
- E.5 PWM Registers 117
- E.6 Quadrature Decoder 118
- Rejected 118
- Accepted 118
- Peri Clock 118
- Timer A10 118
- User’s Manual 113 119
- 114 RabbitCore RCM3200 120
- NOTICE TO USERS 121
- 116 RabbitCore RCM3200 122
- User’s Manual 117 123
- 118 RabbitCore RCM3200 124
- User’s Manual 119 125
- 120 RabbitCore RCM3200 126
- SCHEMATICS 127
Relacionado con productos y manuales para Placas base Rabbit RCM3200
Placas base Rabbit RCM2000 Manual de usuario
(80 paginas)
(80 paginas)
Placas base Rabbit RCM2000 Especificaciones
(40 paginas)
(40 paginas)
Placas base Rabbit BL1800 Manual de usuario
(94 paginas)
(94 paginas)
Placas base Rabbit BL1800 Manual de usuario
(2 paginas)
(2 paginas)
Placas base Rabbit RCM3000 Especificaciones
(44 paginas)
(44 paginas)
Placas base Rabbit RCM3100 Manual de usuario
(1 paginas)
(1 paginas)
Placas base Rabbit RCM3100 Manual de usuario
(2 paginas)
(2 paginas)
Placas base Rabbit RCM2300 Manual de usuario
(78 paginas)
(78 paginas)
Placas base Rabbit RCM2200 Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 1.796 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales